Up to 37% in savings when you subscribe to hi-fi+
hifi-logo-footer

Begin typing your search above and press return to search. Press Esc to cancel.

Moor Amps Ltd is proud to introduce the Angel 6 Power Amplifier and the Angel Pre Preamplifier.

Moor Amps Ltd is proud to introduce the Angel 6 Power Amplifier and the Angel Pre Preamplifier.

The Angel-6 power amplifier is a revolutionary combination of low-feedback purity with high power delivery and control.

These amplifiers are the culmination of a 30 year journey, discovering how to make truly musical amplifiers. It turned out a new approach from the ground up was needed to achieve the stunning musicality of these amplifiers.

The Angel-6 design goes to great lengths to maximise the linearity of every single stage of the amplifier, then applies a low level of overall feedback just to ‘tidy things up’. We use 6 output transistors per channel to ensure this linearity is still maintained even when driving dynamic impedance dips down to 2 ohms with difficult loudspeakers.

The highly linear, low feedback design gives wonderful transparency and realism to in

, Moor Amps Ltd is proud to introduce the Angel 6 Power Amplifier and the Angel Pre Preamplifier.

 

The Angel-6 power amplifier is a revolutionary combination of low-feedback purity with high power delivery and control.

These amplifiers are the culmination of a 30 year journey, discovering how to make truly musical amplifiers. It turned out a new approach from the ground up was needed to achieve the stunning musicality of these amplifiers.

The Angel-6 design goes to great lengths to maximise the linearity of every single stage of the amplifier, then applies a low level of overall feedback just to ‘tidy things up’. We use 6 output transistors per channel to ensure this linearity is still maintained even when driving dynamic impedance dips down to 2 ohms with difficult loudspeakers.

The highly linear, low feedback design gives wonderful transparency and realism to instruments and vocals, and preserves dynamic range without compression. The power and scale of the musical performance is delivered without the hardening up of the sound which most amplifiers suffer when the levels go up. And with 300W RMS per channel into 4 ohms on tap, the levels can most certainly go up!

A low-feedback amplifier design needs a good power supply to perform at its best. Each channel of the dual-mono Angel-6 uses a 3-island regulated power supply with over 100,000uF of high quality capacitors to provide rock-solid power supply stability.

The massive custom low noise transformer is mated to a heavy casing with machined panels of differing thicknesses to damp resonances and prevent microphony effects on the internal components. This allows the power amplifier to sit near the speakers without ill effects, and benefit from short speaker cables to maximise damping of the drive units. It translates into exquisite timing and rhythm.

If you do have the power amp remote from the preamp and sources,XLR balanced inputs allow longer cable runs with high quality, and the standby lead allows the Angel-Pre preamplifier to put the power amp into standby mode.

In short, at Moor Amps we leave no stone un-turned in our quest to achieve effortless musical performance from our amplifiers.

, Moor Amps Ltd is proud to introduce the Angel 6 Power Amplifier and the Angel Pre Preamplifier.

 

The Pre-Amplifier, Moor Amps Ltd is proud to introduce the Angel 6 Power Amplifier and the Angel Pre Preamplifier.As you might expect, our Angel-Pre preamplifier is a little bit different too! 

We needed to find the best pre-amplifier design to match the transparency and neutrality of the Angel power amps.

After much experimentation we found a simple passive-preamp, linked to a top quality volume potentiometer and unity gain output buffers to drive output cables delivered the transparency we needed.

We couple these with the best gold crosspoint signal relayswe can find for the signal routing, and turned (machined) phono connectors to ensure reliable long life connections in and out of the preamp.

The analogue power supplies are separated from the digital section, and like the power amps we use machined panels to damp out vibration and resonances.

While the analogue path is kept simple to give the best sound quality, the digital side is more complex to allow easy system integration.

The motorised volume control allows easy local or remote volume adjustment, and the volume control knob is machined from solid aluminium for a lovely tactile feel. There are 4 line level inputs for your source components, and a G=1, or Unity Gain input to connect to your AV system. The soft-acting mute can be selected as quiet or silent as you choose. 

Oh, and the remote –it’s locally hewn from a billet of aluminium, it feels gorgeous in the hand, the buttons use real switches, they are a long lasting positive joy to use…

Both the Angel-6 and the Angel-Pre are available to purchase now.  

RRP for the Angel-6 is £7495.00

RRP for the Angel-Pre is £2495.00

For more informationand images please email Ruth Narramore [email protected]

For technical assistance please email [email protected]

To view the website please go to www.mooramps.co.uk

Adblocker Detected

"Neque porro quisquam est qui dolorem ipsum quia dolor sit amet, consectetur, adipisci velit..."

"There is no one who loves pain itself, who seeks after it and wants to have it, simply because it is pain..."